Your "One-Stop-Shop" for your next Embedded Project

Stacks Image 17873

OVERVIEW: SEGGER Development Tools - J-Link Adapters


2. Choose your Product:



JTAG Isolator

J-Link JTAG Isolator

Price: € 198,-- excl. VAT

The J-Link JTAG Isolator can be connected between J-Link and any ARM-board that uses the standard 20-pin JTAG-ARM connector to provide electrical isolation. This is essential when the development tools are not connected to the same ground as the application. It is also useful to protect the development tools from electrical spikes that often occur in some applications, such as motor control applications. This product is compatible with J-Link, J-Link Pro and Flasher ARM.

Choose J-Link JTAG Isolator



SWD Isolator

J-Link SWD Isolator

Price: € 198,-- excl. VAT

The J-Link SWD Isolator can be connected between J-Link and any ARM-board that uses the standard 20-pin 0.1" male connector to provide electrical isolation. This is essential when the development tools are not connected to the same ground as the application. It is also useful to protect the development tools from electrical spikes that often occur in some applications, such as motor control applications. Another typical field of application is development of products with sensors or other analog circuitry, in which case the target hardware is protected from electrical noise originating from the development PC.
The J-Link SWD Isolator is compatible with J-Link, J-Link Pro, J-Link Ultra, J-Link Ultra+ and Flasher ARM.

Choose J-Link SWD Isolator



RX Adapter

J-Link RX Adapter

Price: € 98,-- excl. VAT

The J-Link RX Adapter allows JTAG connections between J-Link and target hardware which comes with the Renesas RX600 series MCUs. The J-Link RX adapter is able to optionally power the connected target hardware. 3.3V or 5V supply voltage can be selected using a Jumper. The target is supplied via the VTref connection when the supply option is jumpered.

Choose J-Link RX Adapter



19 Pin Adapter

J-Link 19-pin Cortex-M Adapter

Price: € 32,-- excl. VAT

The J-Link 9-pin Cortex-M Adapter allows JTAG, SWD and SWO connections between J-Link and Cortex-M based target hardware systems. It adapts from the 20-pin 0.1'' JTAG connector to a 19-pin 0.05'' Samtec FTSH connector as defined by ARM.
The J-Link 19-pin Cortex-M Adapter may also be used to connect J-Link to a non Cortex-M target as far as the target connector uses the same pinout as shown below.
By default, TRST is not connected, but the Cortex-M Adapter comes with a solder bridge (NR1) which allows TRST to be connected to pin 9 of the Cortex-M adapter.

Choose J-Link 19-pin Cortex-M Adapter



9 Pin Adapter

J-Link 9-pin Cortex-M Adapter

Price: € 32,-- excl. VAT

The J-Link 9-pin Cortex-M Adapter allows JTAG, SWD and SWO connections between J-Link and Cortex-M based target hardware systems. It adapts from the 20-pin 0.1'' JTAG connector to a 9-pin 0.05'' Samtec FTSH connector as defined by ARM. The J-Link 9-pin Cortex-M Adapter may also be used to connect J-Link to a non Cortex-M target as far as the target connector uses the same pinout as shown below. By default, TRST is not connected, but the Cortex-M Adapter comes with a solder bridge (NR1) which allows TRST to be connected to pin 9 of the Cortex-M adapter.

Choose J-Link 9-pin Cortex-M Adapter



14 Pin Adapter

J-Link ARM 14-pin Adapter

Price: € 68,-- excl. VAT

This adapter allows to use J-Link with ARM7/9/11 targets using this 14-pin 0.1" mating JTAG connector defined by ARM. The 14-pin connector, though defined by ARM as an alternative to the 20-pin connector is not widely used on modern eval boards.

Choose J-Link ARM 14-pin Adapter



14 Pin TI Adapter

J-Link TI 14-pin Adapter

Price: € 49,-- excl. VAT

The J-Link TI 14 pin Adapter allows JTAG connections between J-Link and target hardware which use a TI MCU and provides a 14-pin connector (e.g. the BeagleBoard with an OMAP3530 on it), defined by TI. It adapts from the 20-pin 0.1'' to a 14-pin 0.1'' JTAG connector.

Choose J-Link TI 14-pin Adapter



5V Adapter

J-Link Needle Adapter

Price: € 98,-- excl. VAT

The J-Link Needle Adapter has been designed to connect J-Link to a PCB which does not come with a mating connector or programming header. The designed pattern with 3 locating pins ensures, that the adapter can only be connected in one way. The needle adapter allows manufacturers to save costs and space on their PCBs since there is no need to provide the PCB with additional connectors. It adapts from the 20-pin 0.1'' JTAG to a 10-pin needle connector. J-Link Needle Adapter is compatible to J-Link, J-Link Pro, J-Link ULTRA+, J-Link EDU, Flasher ARM, Flasher RX, Flasher PPC and Flasher Portable.

Choose J-Link Needle Adapter Adapter